如今許多傳統的手工制作已經邁入了數字化、智能化、機械化制造。這樣大大提高生產效率，節約時間和成本。包裝盒制作與生產同樣如此，下面就和一次性外賣打包盒生產廠家一起來了解一下包裝盒制作過程中的流程吧。

Nowadays, many traditional handicrafts have entered digital, intelligent, and mechanized manufacturing. This greatly improves production efficiency, saves time and costs. The same goes for packaging box production. Let's learn about the process of packaging box production with the manufacturer of disposable takeaway packaging boxes.

1.先需要調紙切割成生產規格的面紙。

1. First, it is necessary to adjust and cut the paper into production specifications of face paper.

2.把面紙放在智能印刷設備上印刷面紙。

2. Place the tissue paper on the intelligent printing device to print the tissue paper.

3.制作刀模進行啤，啤是生產工藝的重要環節。在這個環節要進行刀模對位，刀模對不準，嚴重影響整個包裝盒制作的成品。

3. Making a knife mold for beer is an important part of the production process. At this stage, it is necessary to align the knife mold, which can seriously affect the finished product of the entire packaging box.

4.針對面紙過膠，這一工藝流程是為了保護包裝盒子制作出來出現面紙磨花等。

4. This process is aimed at protecting the face paper from scratches and other defects during the production of packaging boxes.

5.面紙卡放到機械手下面，進行貼盒等一系列工藝，這樣半成品包裝盒出來了。

5. Place the tissue paper card under the robotic arm and perform a series of processes such as pasting boxes, so that the semi-finished packaging box comes out.

6.流水線把常規貼好的盒子輸送自動成型機位置，利用人工把貼好的盒子放入成型模具上面，啟動機器，成型機會依次導致長邊，折入長邊，壓泡包短邊，壓泡，機器會把盒子們彈到流水線上。

6. The assembly line transports the conventional pasted boxes to the position of the automatic forming machine. The pasted boxes are manually placed on the forming mold, and the machine is started. The forming process sequentially leads to long edges, folding into long edges, pressing short edges, and pressing bubbles. The machine will bounce the boxes onto the assembly line.

7.經過QC把包好的盒子擺放右邊，用紙板疊好，清潔膠水，檢測不良品。

7. After QC, place the wrapped box on the right side, stack it with cardboard, clean the glue, and detect defective products.

我們?cè)诎b盒制作過程中需要注意一些細節問題，常見的問題需要我們注意：

We need to pay attention to some details during the production process of packaging boxes, and common problems need to be noted:

1.面紙?jiān)谄〉倪^(guò)程中注意正反面，防止面紙過不到膠水，導致盒子邊上開膠。

1. During the beer brewing process, pay attention to the front and back sides of the face paper to prevent it from not passing through the glue and causing the glue to open on the edge of the box.

2.包裝盒卡的時候要注意高低角，否則盒子到成型機上會壓破損。

2. When packaging the box, pay attention to the high and low angles, otherwise the box will be crushed and damaged on the molding machine.

3.在成型機上的時候注意毛刷、毛棍、鏟刀上不能有膠水，這樣也會導致盒子邊上開膠。

3. When using the molding machine, pay attention to the absence of glue on the brushes, bristles, and shovels, as this can also cause glue to open on the edges of the box.

4.膠水的厚度要根據紙張不同進行調節，不能在牙齒上滴膠或者用水性環保白膠。

4. The thickness of the glue should be adjusted according to the different papers, and it cannot be dropped on the teeth or water-based environmentally friendly white glue.

5.還需注意包裝盒不能存在空邊、開膠、膠水痕、耳朵打皺、爆角、定位歪斜偏大（機器定位設置在正負0.1MM左右）。

5. It is also important to note that the packaging box should not have empty edges, glue marks, ear wrinkles, burst corners, or excessive positioning deviation (the machine positioning should be set at around plus or minus 0.1mm).

在整個生產過程中包裝盒在生產之前，都需要先用刀模試出一個樣品來，在確認沒問題之后才進行大批量下料生產，這樣防止假如刀模出了問題也有修改的機會，終確認沒問題才能批量生產，正是有著這種研究的態度才能把包裝盒制作得很好。有什么事項了解就來咨詢我們http://jwwylp.com吧！

Throughout the entire production process, packaging boxes need to be tested with a knife mold before production. After confirming that there are no problems, large-scale production can be carried out. This prevents the possibility of modification if there are problems with the knife mold, and mass production can only be carried out after confirming that there are no problems. It is precisely with this research attitude that packaging boxes can be made very well. If you have any questions, please consult us http://jwwylp.com Come on!